Meccano Set Parts Lists
UK MECCANO SET PARTS LIST
Outfit 4 (1922)
Compiled by Timothy Edwards
| Outfit 4 (1922) | |||||
|---|---|---|---|---|---|
| Set P/N | Modern P/N | Part Description | Quantity | ||
| 1 | Perforated strip 12 1/2" 25hole | 12 | |||
| 2 | Perforated strip 5 1/2" 11hole | 21 | |||
| 2a | Perforated strip 4 1/2" 9hole | 2 | |||
| 3 | Perforated strip 3 1/2" 7hole | 6 | |||
| 4 | Perforated strip 3" 6hole | 6 | |||
| 5 | Perforated strip 2 1/2" 5hole | 18 | |||
| 6a | Perforated strip 1 1/2" 3hole | 2 | |||
| 8 | Angle girder 12 1/2" 25hole | 8 | |||
| 9 | Angle girder 5 1/2" 11hole | 4 | |||
| 10 | Flat Bracket (Fishplate) | 8 | |||
| 11 | Double Angle Bracket | 5 | |||
| 12 | Angle bracket | 22 | |||
| 12a | Angle bracket 1x1" | 4 | |||
| 13 | Axle rod 11 1/2" | 2 | |||
| 13a | Axle rod 8" | 1 | |||
| 14 | Axle rod 6" | 3 | |||
| 15 | Axle rod 5" | 4 | |||
| 15a | Axle rod 4 1/2" | 5 | |||
| 16 | Axle rod 3 1/2" | 5 | |||
| 17 | Axle rod 2" | 5 | |||
| 18a | Axle rod 1 1/2" | 4 | |||
| 19 | 19s/19h | Crank Handle - (length varied 3 1/2" - 5") | 2 | ||
| 19b | Pulley 3" dia, | 1 | |||
| 20 | Flanged wheel 1 1/8" dia | 8 | |||
| 21 | Pulley 1 1/2" dia | 1 | |||
| 22 | Pulley 1" dia | 4 | |||
| 22a | Pulley 1" dia without boss | 3 | |||
| 23 | 23b | Pulley 1/2" dia without boss - metal | 3 | ||
| 24 | Bush wheel 1 3/8" dia, 8 holes | 2 | |||
| 26 | Pinion 1/2"dia, 1/4"face, 19t | 2 | |||
| 27a | Gear wheel 1 1/2"dia,57t | 1 | |||
| 28 | Contrate Gear 1 1/2" dia, 50t | 1 | |||
| 29 | Contrate Gear 3/4" dia, 25t | 2 | |||
| 32 | Worm Gear | 1 | |||
| 33 | Pawl (type 2) with Pivot Bolts | 1 | |||
| 34 | Spanner | 2 | |||
| 35 | Spring clip | 18 | |||
| 36 | Screwdriver - Standard Bent Rod | 1 | |||
| 37 | Square Nut and bolt (bolt 5/16" long) | 130 | |||
| 38 | Washer 3/8" dia. | 24 | |||
| 40 | Hank of cord | 4 | |||
| 43 | Tension Spring 2" | 1 | |||
| 44 | Cranked bent strip | 1 | |||
| 45 | Double bent strip | 3 | |||
| 46 | Double angle strip 2 1/2x1" | 2 | |||
| 52 | Flanged Plate 5 1/2x2 1/2" - 2 flanges (See Note below) | 2 | |||
| 53 | Flanged plate 3 1/2x2 1/2" | 5 | |||
| 54 | Flanged sector plate 4" | 3 | |||
| 57 | Wire Hook | 1 | |||
| 59 | Collar | 10 | |||
| 60 | 48a | Bent strips 2 1/2" | 10 | ||
| 60a | 48 | Bent strips 1 1/2" | 2 | ||
| 60b | 48b | Bent strips 3 1/2" | 6 | ||
| 60c | 48d | Bent strips 5 1/2" | 2 | ||
| 61 | Windmill sail | 4 | |||
| 62 | Crank | 2 | |||
| 63 | Coupling | 6 | |||
| 65 | Centre fork | 1 | |||
| 77 | Trangular plate 1" | 2 | |||
| 90 | Curved strip 2 1/2", 2 3/8"r | 4 | |||
| 94 | Sprocket chain | 3ft | |||
| 95 | Sprocket wheel 2"d, 36t | 1 | |||
| 96 | Sprocket wheel 1"d, 18t | 2 | |||
| 98 | Braced girder 2 1/2" 5hole - double open | 1 | |||
| 99 | Braced girder 12 1/2" 25hole -double open | 4 | |||
| 100 | Braced girder 5 1/2" 11hole - double open | 6 | |||
| 103f | Flat girder 2 1/2" 5hole | 2 | |||
| 108 | Architrave (Corner Gusset) | 2 | |||
| 109 | Face plate 2 1/2"d | 1 | |||
| 111 | Bolt 3/4" | 3 | |||
| 115 | Threaded pin - Round Shoulder | 2 | |||
| 125 | Reverse angle bracket 1/2" | 4 | |||
| 126a | Flat trunnion | 4 | |||
| 130 | Eccentric, Triple Throw | 2 | |||
| 134 | Crank shaft 1" stroke | 1 | |||
NOTES
1. The 5 1/2" x 2 1/2" flanged plates initially had two flanges on the long sides. The four flanged version was announced in the May 1928 Meccano Magazine. Whilst these lists assume that this happened in 1928, this is not necessarily certain and there might well have been a delay whilst old stock was used up. This especially applies to sets for overseas. There is some evidence to suggest that the 1930 Outfit 000 had the two flanged version.
2. From 1927 to 1934 the 5 1/2" x 2 1/2" flanged plates (both two & four flanged versions) also had a sawcut and slot to accommodate the circular saw (Part No. 159).
3. Originally all bosses were single tapped. In 1926/7 all bosses became double tapped.