Meccano Set Parts Lists
UK MECCANO SET PARTS LIST
Outfit 6 (1924 Late)
Compiled by Timothy Edwards
Outfit 6 (1924 Late) | |||||
---|---|---|---|---|---|
Set P/N | Modern P/N | Part Description | Quantity | ||
1 | Perforated strip 12 1/2" 25hole | 48 | |||
1a | Perforated strip 9 1/2" 19hole | 2 | |||
1b | Perforated strip 7 1/2" 15hole | 4 | |||
2 | Perforated strip 5 1/2" 11hole | 50 | |||
2a | Perforated strip 4 1/2" 9hole | 4 | |||
3 | Perforated strip 3 1/2" 7hole | 24 | |||
4 | Perforated strip 3" 6hole | 10 | |||
5 | Perforated strip 2 1/2" 5hole | 36 | |||
6 | Perforated strip 2" 4hole | 24 | |||
6a | Perforated strip 1 1/2" 3hole | 14 | |||
8 | Angle girder 12 1/2" 25hole | 26 | |||
8a | Angle girder 9 1/2" 19hole | 6 | |||
9 | Angle girder 5 1/2" 11hole | 18 | |||
9a | Angle girder 4 1/2" 9hole | 2 | |||
9b | Angle girder 3 1/2" 7hole | 2 | |||
9d | Angle girder 2 1/2" 5hole | 4 | |||
9f | Angle girder 1 1/2" 3hole | 4 | |||
10 | Flat Bracket (Fishplate) | 16 | |||
11 | Double Angle Bracket | 8 | |||
12 | Angle bracket | 48 | |||
12a | Angle bracket 1x1" | 4 | |||
12b | Angle bracket 1x1/2" | 4 | |||
13 | Axle rod 11 1/2" | 4 | |||
13a | Axle rod 8" | 4 | |||
14 | Axle rod 6 1/2" | 4 | |||
15 | Axle rod 5" | 4 | |||
15a | Axle rod 4 1/2" | 5 | |||
16 | Axle rod 3 1/2" | 5 | |||
16a | Axle rod 2 1/2" | 2 | |||
16b | Axle rod 3" | 2 | |||
17 | Axle rod 2" | 5 | |||
18a | Axle rod 1 1/2" | 4 | |||
18b | Axle rod 1" | 2 | |||
19 | 19s/19h | Crank Handle - (length varied 3 1/2" - 5") | 4 | ||
19a | Spoked Wheel 3", with boss | 4 | |||
19b | Pulley 3" dia, | 2 | |||
20 | Flanged wheel 1 1/8" dia | 8 | |||
20a | Pulley 2" dia | 1 | |||
21 | Pulley 1 1/2" dia | 2 | |||
22 | Pulley 1" dia | 6 | |||
22a | Pulley 1" dia without boss | 4 | |||
23 | 23b | Pulley 1/2" dia without boss - metal | 6 | ||
24 | Bush wheel 1 3/8" dia, 8 holes | 4 | |||
25 | Pinion 3/4"dia, 1/4"face, 25t | 2 | |||
26 | Pinion 1/2"dia, 1/4"face, 19t | 6 | |||
27 | Gear wheel 1 1/4"dia, 50t | 2 | |||
27a | Gear wheel 1 1/2"dia,57t | 3 | |||
28 | Contrate Gear 1 1/2" dia, 50t | 2 | |||
29 | Contrate Gear 3/4" dia, 25t | 2 | |||
32 | Worm Gear | 2 | |||
33 | Pawl (type 2) with Pivot Bolts | 1 | |||
34 | Spanner | 2 | |||
35 | Spring clip | 24 | |||
36 | Screwdriver - Standard Bent Rod | 1 | |||
36a | Screwdriver - Extra Long (bent rod handle) | 1 | |||
37 | Square Nut and bolt (bolt 7/32" long) | 320 | |||
38 | Washer 3/8" dia. | 36 | |||
40 | Hank of cord | 6 | |||
41 | Propeller Blade - type 1 (wide) | 4 | |||
43 | Tension Spring 2" | 2 | |||
44 | Cranked bent strip | 2 | |||
45 | Double bent strip | 6 | |||
46 | Double angle strip 2 1/2x1" | 4 | |||
47 | Double angle strip 2 1/2x1 1/2" | 2 | |||
47a | Double angle strip 3x1 1/2" | 2 | |||
48 | Double angle strip 1 1/2x1/2" | 4 | |||
48a | Double angle strip 2 1/2x1/2" | 16 | |||
48b | Double angle strip 3 1/2x1/2" | 6 | |||
48c | Double angle strip 4 1/2x1/2" | 3 | |||
48d | Double angle strip 5 1/2x1/2" | 4 | |||
50 | Eye piece without boss | 2 | |||
52 | Flanged Plate 5 1/2x2 1/2" - 2 flanges (See Note below) | 7 | |||
52a | Flat plate 5 1/2x3 1/2" | 2 | |||
53 | Flanged plate 3 1/2x2 1/2" | 8 | |||
53a | Flat plate 4 1/2x2 1/2" | 1 | |||
54 | Flanged sector plate 4" | 4 | |||
57 | Wire Hook | 6 | |||
57b | Loaded Hook (large) - ball type | 1 | |||
58 | Spring cord 40" | 1 | |||
59 | Collar | 21 | |||
61 | Windmill sail | 4 | |||
62 | Crank | 4 | |||
62a | Threaded Crank | 2 | |||
63 | Coupling | 9 | |||
63b | Octagonal Strip Coupling | 2 | |||
64 | Threaded boss | 3 | |||
65 | Centre fork | 1 | |||
70 | Flat plate 5 1/2x2 1/2" | 3 | |||
72 | Flat plate 2 1/2x2 1/2" | 2 | |||
76 | Trangular plate 2 1/2" | 2 | |||
77 | Trangular plate 1" | 3 | |||
80a | Screwed rod 3 1/2" | 2 | |||
81 | Screwed rod 2" | 1 | |||
89 | Curved strip 5 1/2", 10"r | 4 | |||
90 | Curved strip 2 1/2", 2 3/8"r | 16 | |||
94 | Sprocket chain | 8ft | |||
95 | Sprocket wheel 2"d, 36t | 3 | |||
95a | Sprocket wheel 1 1/2"d, 28t | 1 | |||
96 | Sprocket wheel 1"d, 18t | 4 | |||
96a | Sprocket wheel 3/4"d, 14t | 1 | |||
97 | Braced girder 3 1/2" 7hole - double open | 4 | |||
98 | Braced girder 2 1/2" 5hole - double open | 8 | |||
99 | Braced girder 12 1/2" 25hole -double open | 8 | |||
100 | Braced girder 5 1/2" 11hole - double open | 8 | |||
102 | Single bent strip | 2 | |||
103f | Flat girder 2 1/2" 5hole | 2 | |||
103h | Flat girder 1 1/2" 3hole | 1 | |||
108 | Architrave (Corner Gusset) | 4 | |||
109 | Face plate 2 1/2"d | 2 | |||
110 | Rack strip 3 1/2" | 2 | |||
111 | Bolt 3/4" | 3 | |||
111a | Bolt 1/2" | 1 | |||
115 | Threaded pin - Round Shoulder | 2 | |||
116 | Fork piece, Large | 2 | |||
118 | Hub disc 5 1/2" dia | 1 | |||
123 | Cone pulley | 1 | |||
124 | Reverse angle bracket 1" | 2 | |||
125 | Reverse angle bracket 1/2" | 4 | |||
126 | Trunnion | 3 | |||
126a | Flat trunnion | 5 | |||
128 | Bell Crank with boss | 2 | |||
130 | Eccentric, Triple Throw | 2 | |||
133 | Corner bracket 1/12" | 8 | |||
134 | Crank shaft 1" stroke | 1 | |||
135 | Theodolite protractor | 1 | |||
136 | Handrail Support | 4 | |||
137 | Wheel flange | 1 | |||
143 | Circular girder 5 1/2" dia | 1 |
NOTES
1. The 5 1/2" x 2 1/2" flanged plates initially had two flanges on the long sides. The four flanged version was announced in the May 1928 Meccano Magazine. Whilst these lists assume that this happened in 1928, this is not necessarily certain and there might well have been a delay whilst old stock was used up. This especially applies to sets for overseas. There is some evidence to suggest that the 1930 Outfit 000 had the two flanged version.
2. From 1927 to 1934 the 5 1/2" x 2 1/2" flanged plates (both two & four flanged versions) also had a sawcut and slot to accommodate the circular saw (Part No. 159).
3. Originally all bosses were single tapped. In 1926/7 all bosses became double tapped.