Meccano Set Parts Lists

UK MECCANO SET PARTS LIST
Outfit 7 (1924 Mid)

Compiled by Timothy Edwards


 
 
Outfit 7 (1924 Mid)
Set P/N Modern P/N Part Description Quantity
1 Perforated strip 12 1/2" 25hole 50
1a Perforated strip 9 1/2" 19hole 12
2 Perforated strip 5 1/2" 11hole 75
2a Perforated strip 4 1/2" 9hole 4
3 Perforated strip 3 1/2" 7hole 24
4 Perforated strip 3" 6hole 36
5 Perforated strip 2 1/2" 5hole 120
6 Perforated strip 2" 4hole 36
6a Perforated strip 1 1/2" 3hole 14
7 Angle girder 24 1/2" 49hole 12
7a Angle girder 18 1/2" 37hole 6
8 Angle girder 12 1/2" 25hole 24
8a Angle girder 9 1/2" 19hole 12
9 Angle girder 5 1/2" 11hole 24
9d Angle girder 2 1/2" 5hole 1
10 Flat Bracket (Fishplate) 24
11 Double Angle Bracket 18
12 Angle bracket 96
12a Angle bracket 1x1" 12
12b Angle bracket 1x1/2" 3
13 Axle rod 11 1/2" 8
13a Axle rod 8" 13
14 Axle rod 6 1/2" 13
15 Axle rod 5" 7
15a Axle rod 4 1/2" 6
16 Axle rod 3 1/2" 12
16a Axle rod 2 1/2" 4
17 Axle rod 2" 14
18a Axle rod 1 1/2" 8
18b Axle rod 1" 6
19 19s/19hCrank Handle - (length varied 3 1/2" - 5") 3
19a Spoked Wheel 3", with boss 4
19b Pulley 3" dia, 4
20 Flanged wheel 1 1/8" dia 19
20a Pulley 2" dia 4
21 Pulley 1 1/2" dia 6
22 Pulley 1" dia 6
22a Pulley 1" dia without boss 13
23 23bPulley 1/2" dia without boss - metal 8
23a Pulley 1/2" dia with boss 2
24 Bush wheel 1 3/8" dia, 8 holes 5
25 Pinion 3/4"dia, 1/4"face, 25t 5
26 Pinion 1/2"dia, 1/4"face, 19t 7
27 Gear wheel 1 1/4"dia, 50t 5
27a Gear wheel 1 1/2"dia,57t 7
28 Contrate Gear 1 1/2" dia, 50t 2
29 Contrate Gear 3/4" dia, 25t 4
30 Bevel Gear 7/8"dia, 26t 4
31 Gear Wheel 1"dia, 1/4"face, 38t 3
32 Worm Gear 2
33 Pawl (type 2) with Pivot Bolts 2
33a 147bPivot Bolt with nuts 2
34 Spanner 2
35 Spring clip 36
36 Screwdriver - Standard Bent Rod 1
36a Screwdriver - Extra Long (bent rod handle) 1
37 Square Nut and bolt (bolt 5/16" long) 600
37b Bolt, 5/16" long 8
38 Washer 3/8" dia. 200
40 Hank of cord 6
41 Propeller Blade - type 1 (wide) 8
43 Tension Spring 2" 15
44 Cranked bent strip 3
45 Double bent strip 8
46 Double angle strip 2 1/2x1" 4
47 Double angle strip 2 1/2x1 1/2" 2
47a Double angle strip 3x1 1/2" 2
48 Double angle strip 1 1/2x1/2" 5
48a Double angle strip 2 1/2x1/2" 24
48b Double angle strip 3 1/2x1/2" 12
48c Double angle strip 4 1/2x1/2" 3
48d Double angle strip 5 1/2x1/2" 7
50 Eye piece without boss 2
52 Flanged Plate 5 1/2x2 1/2" - 2 flanges (See Note below) 7
52a Flat plate 5 1/2x3 1/2" 8
53 Flanged plate 3 1/2x2 1/2" 10
53a Flat plate 4 1/2x2 1/2" 1
54 Flanged sector plate 4" 4
57 Wire Hook 17
57a Scientific Hook 6
57b Loaded Hook (large) - ball type 2
58 Spring cord 40" 1
59 Collar 55
61 Windmill sail 4
62 Crank 15
62a Threaded Crank 2
63 Coupling 13
63a Octagonal Coupling 1
63b Octagonal Strip Coupling 1
64 Threaded boss 2
65 Centre fork 6
66 Weight, 50 gramme 5
67 Weight, 25 gramme 5
70 Flat plate 5 1/2x2 1/2" 4
72 Flat plate 2 1/2x2 1/2" 2
76 Trangular plate 2 1/2" 4
77 Trangular plate 1" 10
78 Screwed rod 11 1/2" 2
80 Screwed rod 5" 2
80a Screwed rod 3 1/2" 1
81 Screwed rod 2" 2
82 Screwed rod 1" 4
89 Curved strip 5 1/2", 10"r 6
90 Curved strip 2 1/2", 2 3/8"r 6
94 Sprocket chain 25ft
95 Sprocket wheel 2"d, 36t 3
95a Sprocket wheel 1 1/2"d, 28t 1
95b Sprocket wheel 3"d, 56t 1
96 Sprocket wheel 1"d, 18t 17
96a Sprocket wheel 3/4"d, 14t 1
97 Braced girder 3 1/2" 7hole - double open 4
98 Braced girder 2 1/2" 5hole - double open 8
99 Braced girder 12 1/2" 25hole -double open 18
100 Braced girder 5 1/2" 11hole - double open 16
101 Hearld, for loom 48
102 Single bent strip 2
103 Flat girder 5 1/2" 11hole 6
103b Flat girder 12 1/2" 25hole 1
103f Flat girder 2 1/2" 5hole 2
104 Shuttle, for loom 1
105 Reed hook, for loom 1
106 Wooden roller 2
106a Sand roller 1
107 Table for designing machine 1
108 Architrave (Corner Gusset) 4
109 Face plate 2 1/2"d 4
110 Rack strip 3 1/2" 2
111 Bolt 3/4" 3
111b 37bBolt 5/32" 1
113 Girder frame 4
114 Hinge 2
115 Threaded pin - Round Shoulder 4
116 Fork piece, Large 2
122 Miniature loaded sack 12
123 Cone pulley 1
124 Reverse angle bracket 1" 2
125 Reverse angle bracket 1/2" 4
126 Trunnion 2
126a Flat trunnion 6
128 Bell Crank with boss 1
130 Eccentric, Triple Throw 2
131 Dredger bucket 5
132 Flywheel 2 3/4" dia 1
134 Crank shaft 1" stroke 1
135 Theodolite protractor 1
138 Ship's funnel - vertical 2
301 181Bobbins 2
302 182Insulating brushes 12
303 1570/182aInsulating washers (also #1570) 12
304 15756 b.a.screw (also #1575) 14
305 15836 b.a. nut (also #1583) 30
306 1563Terminals (also #1563) 4
307 Contact screws 2
308 Pole pieces 2
309 Coil cheeks 2
310 183Lamp holder (also #183) 1
311 184cLamps 1
312 27 swg iron wire 1
313 26 swg SCC wire (50 yards) 1
314 23 swg SCC wire (25 yards) 1
315 Bare copper wire (4 yards) 1
? Accumulator 4V 1
No.1A Clockwork Motor Reversing (Num from 31/2) 1
? Electric motor 4V Reversing 1
Electric Outfit Manual 1
Motor Chassis Leaflet 1
Loom leaflet 1
Charging Board Leaflet 1

NOTES

1. The 5 1/2" x 2 1/2" flanged plates initially had two flanges on the long sides. The four flanged version was announced in the May 1928 Meccano Magazine. Whilst these lists assume that this happened in 1928, this is not necessarily certain and there might well have been a delay whilst old stock was used up. This especially applies to sets for overseas. There is some evidence to suggest that the 1930 Outfit 000 had the two flanged version.

2. From 1927 to 1934 the 5 1/2" x 2 1/2" flanged plates (both two & four flanged versions) also had a sawcut and slot to accommodate the circular saw (Part No. 159).

3. Originally all bosses were single tapped. In 1926/7 all bosses became double tapped.