Meccano Set Parts Lists

UK MECCANO SET PARTS LIST
Outfit 5 (1926)

Compiled by Timothy Edwards


 
 
Outfit 5 (1926)
Set P/N Modern P/N Part Description Quantity
1 Perforated strip 12 1/2" 25hole 16
2 Perforated strip 5 1/2" 11hole 26
2a Perforated strip 4 1/2" 9hole 4
3 Perforated strip 3 1/2" 7hole 12
4 Perforated strip 3" 6hole 8
5 Perforated strip 2 1/2" 5hole 36
6 Perforated strip 2" 4hole 4
6a Perforated strip 1 1/2" 3hole 6
8 Angle girder 12 1/2" 25hole 14
8a Angle girder 9 1/2" 19hole 4
9 Angle girder 5 1/2" 11hole 4
9d Angle girder 2 1/2" 5hole 1
10 Flat Bracket (Fishplate) 12
11 Double Angle Bracket 8
12 Angle bracket 36
12a Angle bracket 1x1" 4
13 Axle rod 11 1/2" 2
13a Axle rod 8" 1
14 Axle rod 6 1/2" 3
15 Axle rod 5" 4
15a Axle rod 4 1/2" 5
16 Axle rod 3 1/2" 5
17 Axle rod 2" 5
18a Axle rod 1 1/2" 4
19 19s/19hCrank Handle - (length varied 3 1/2" - 5") 2
19a Spoked Wheel 3", with boss 4
19b Pulley 3" dia, 2
20 Flanged wheel 1 1/8" dia 8
21 Pulley 1 1/2" dia 2
22 Pulley 1" dia 4
22a Pulley 1" dia without boss 3
23 23bPulley 1/2" dia without boss - metal 3
24 Bush wheel 1 3/8" dia, 8 holes 2
26 Pinion 1/2"dia, 1/4"face, 19t 3
27a Gear wheel 1 1/2"dia,57t 2
28 Contrate Gear 1 1/2" dia, 50t 1
29 Contrate Gear 3/4" dia, 25t 2
32 Worm Gear 1
34 Spanner 2
35 Spring clip 18
36 Screwdriver - Standard Bent Rod 1
36a Screwdriver - Extra Long (bent rod handle) 1
37 Square Nut and bolt (bolt 7/32" long) 169
37a Square Nut 6
38 Washer 3/8" dia. 24
40 Hank of cord 6
41 Propeller Blade - type 1 (wide) 2
43 Tension Spring 2" 1
44 Cranked bent strip 1
45 Double bent strip 3
46 Double angle strip 2 1/2x1" 4
47 Double angle strip 2 1/2x1 1/2" 1
47a Double angle strip 3x1 1/2" 2
48 Double angle strip 1 1/2x1/2" 2
48a Double angle strip 2 1/2x1/2" 10
48b Double angle strip 3 1/2x1/2" 6
48d Double angle strip 5 1/2x1/2" 4
50 Eye piece without boss 1
52 Flanged Plate 5 1/2x2 1/2" - 2 flanges (See Note below) 4
52a Flat plate 5 1/2x3 1/2" 2
53 Flanged plate 3 1/2x2 1/2" 5
54 Flanged sector plate 4" 3
57 Wire Hook 2
59 Collar 13
61 Windmill sail 4
62 Crank 2
63 Coupling 6
65 Centre fork 1
70 Flat plate 5 1/2x2 1/2" 1
77 Trangular plate 1" 2
80a Screwed rod 3 1/2" 1
89 Curved strip 5 1/2", 10"r 4
90 Curved strip 2 1/2", 2 3/8"r 6
90a Curved strip stepped, 2 1/2", 1 3/8r 4
94 Sprocket chain 3ft
95 Sprocket wheel 2"d, 36t 2
96 Sprocket wheel 1"d, 18t 2
98 Braced girder 2 1/2" 5hole - double open 1
99 Braced girder 12 1/2" 25hole -double open 4
100 Braced girder 5 1/2" 11hole - double open 7
102 Single bent strip 2
103f Flat girder 2 1/2" 5hole 2
108 Architrave (Corner Gusset) 2
109 Face plate 2 1/2"d 1
111 Bolt 3/4" 3
111c Bolt 3/8" 6
115 Threaded pin - Round Shoulder 2
116 Fork piece, Large 1
125 Reverse angle bracket 1/2" 4
126a Flat trunnion 5
128 Bell Crank with boss 1
130 Eccentric, Triple Throw 2
134 Crank shaft 1" stroke 1
147a Pawl with boss 1
147b Pivot Bolt with nuts 1
148 Ratchet wheel 1
56c Standard Mechanisms 1

NOTES

1. The 5 1/2" x 2 1/2" flanged plates initially had two flanges on the long sides. The four flanged version was announced in the May 1928 Meccano Magazine. Whilst these lists assume that this happened in 1928, this is not necessarily certain and there might well have been a delay whilst old stock was used up. This especially applies to sets for overseas. There is some evidence to suggest that the 1930 Outfit 000 had the two flanged version.

2. From 1927 to 1934 the 5 1/2" x 2 1/2" flanged plates (both two & four flanged versions) also had a sawcut and slot to accommodate the circular saw (Part No. 159).

3. Originally all bosses were single tapped. In 1926/7 all bosses became double tapped.