Meccano Set Parts Lists
UK MECCANO SET PARTS LIST
Outfit 2 (1932-35)
Compiled by Timothy Edwards
| Outfit 2 (1932-35) | |||||
|---|---|---|---|---|---|
| Set P/N | Modern P/N | Part Description | Quantity | ||
| 1 | Perforated strip 12 1/2" 25hole | 10 | |||
| 2 | Perforated strip 5 1/2" 11hole | 14 | |||
| 3 | Perforated strip 3 1/2" 7hole | 2 | |||
| 5 | Perforated strip 2 1/2" 5hole | 12 | |||
| 6a | Perforated strip 1 1/2" 3hole | 2 | |||
| 8 | Angle girder 12 1/2" 25hole | 4 | |||
| 10 | Flat Bracket (Fishplate) | 8 | |||
| 11 | Double Angle Bracket | 4 | |||
| 12 | Angle bracket | 12 | |||
| 12a | Angle bracket 1x1" | 2 | |||
| 13 | Axle rod 11 1/2" | 1 | |||
| 15 | Axle rod 5" | 2 | |||
| 15a | Axle rod 4 1/2" | 1 | |||
| 16 | Axle rod 3 1/2" | 4 | |||
| 17 | Axle rod 2" | 2 | |||
| 18a | Axle rod 1 1/2" | 4 | |||
| 19 | 19h | Crank handle - large (5") | 1 | ||
| 19b | Pulley 3" dia, | 4 | |||
| 19s | Crank handle - small (3 1/2") | 1 | |||
| 20b | Flanged wheel 3/4" dia] | 4 | |||
| 22 | Pulley 1" dia | 4 | |||
| 22a | Pulley 1" dia without boss | 2 | |||
| 23 | 23b | Pulley 1/2" dia without boss - metal | 1 | ||
| 24 | Bush wheel 1 3/8" dia, 8 holes | 1 | |||
| 34 | Spanner | 1 | |||
| 35 | Spring clip | 14 | |||
| 36 | Screwdriver - Standard Bent Rod | 1 | |||
| 37 | Square Nut and bolt (bolt 7/32" long) | 60 | |||
| 37a | Square Nut | 6 | |||
| 38 | Washer 3/8" dia. | 14 | |||
| 40 | Hank of cord | 2 | |||
| 44 | Cranked bent strip | 1 | |||
| 45 | Double bent strip | 1 | |||
| 48 | Double angle strip 1 1/2x1/2" | 1 | |||
| 48a | Double angle strip 2 1/2x1/2" | 8 | |||
| 52 | Flanged Plate 5 1/2x2 1/2" - 4 flanges (See Note below) | 1 | |||
| 54 | Flanged sector plate 4" | 2 | |||
| 57c | Loaded Hook (small) - ball Type | 1 | |||
| 62 | Crank | 2 | |||
| 90a | Curved strip stepped, 2 1/2", 1 3/8r | 4 | |||
| 99 | Braced girder 12 1/2" 25hole - double closed | 2 | |||
| 100 | Braced girder 5 1/2" 11hole - double closed | 2 | |||
| 111c | Bolt 3/8" | 6 | |||
| 115 | Threaded pin - Square Shoulder | 1 | |||
| 125 | Reverse angle bracket 1/2" | 4 | |||
| 126 | Trunnion | 2 | |||
| 126a | Flat trunnion | 2 | |||
NOTES
1. The 5 1/2" x 2 1/2" flanged plates initially had two flanges on the long sides. The four flanged version was announced in the May 1928 Meccano Magazine. Whilst these lists assume that this happened in 1928, this is not necessarily certain and there might well have been a delay whilst old stock was used up. This especially applies to sets for overseas. There is some evidence to suggest that the 1930 Outfit 000 had the two flanged version.
2. From 1927 to 1934 the 5 1/2" x 2 1/2" flanged plates (both two & four flanged versions) also had a sawcut and slot to accommodate the circular saw (Part No. 159).
3. Originally all bosses were single tapped. In 1926/7 all bosses became double tapped.