Meccano Set Parts Lists

UK MECCANO SET PARTS LIST
Outfit 7 (1934)

Compiled by Timothy Edwards


 
 
Outfit 7 (1934)
Set P/N Modern P/N Part Description Quantity
1 Perforated strip 12 1/2" 25hole 38
1a Perforated strip 9 1/2" 19hole 16
1b Perforated strip 7 1/2" 15hole 13
2 Perforated strip 5 1/2" 11hole 40
2a Perforated strip 4 1/2" 9hole 12
3 Perforated strip 3 1/2" 7hole 24
4 Perforated strip 3" 6hole 24
5 Perforated strip 2 1/2" 5hole 120
6 Perforated strip 2" 4hole 30
6a Perforated strip 1 1/2" 3hole 14
7 Angle girder 24 1/2" 49hole 12
7a Angle girder 18 1/2" 37hole 6
8 Angle girder 12 1/2" 25hole 26
8a Angle girder 9 1/2" 19hole 17
8b Angle girder 7 1/2" 15hole 8
9 Angle girder 5 1/2" 11hole 24
9a Angle girder 4 1/2" 9hole 15
9b Angle girder 3 1/2" 7hole 7
9c Angle girder 3" 6hole 3
9d Angle girder 2 1/2" 5hole 7
9e Angle girder 2" 4hole 2
9f Angle girder 1 1/2" 3hole 4
10 Flat Bracket (Fishplate) 30
11 Double Angle Bracket 12
12 Angle bracket 76
12a Angle bracket 1x1" 12
12b Angle bracket 1x1/2" 16
13 Axle rod 11 1/2" 8
13a Axle rod 8" 7
14 Axle rod 6 1/2" 13
15 Axle rod 5" 6
15a Axle rod 4 1/2" 6
16 Axle rod 3 1/2" 12
16a Axle rod 2 1/2" 13
16b Axle rod 3" 5
17 Axle rod 2" 12
18a Axle rod 1 1/2" 9
18b Axle rod 1" 7
19 19hCrank handle - large (5") 3
19a Spoked Wheel 3", with boss 4
19b Pulley 3" dia, 4
19s Crank handle - small (3 1/2") 1
20 Flanged wheel 1 1/8" dia 12
20a Pulley 2" dia 4
20b Flanged wheel 3/4" dia] 10
21 Pulley 1 1/2" dia 4
22 Pulley 1" dia 10
22a Pulley 1" dia without boss 15
23 23bPulley 1/2" dia without boss - metal 6
23a Pulley 1/2" dia with boss 4
24 Bush wheel 1 3/8" dia, 8 holes 8
25 Pinion 3/4"dia, 1/4"face, 25t 5
26 Pinion 1/2"dia, 1/4"face, 19t 9
26a Pinion 1/2"dia, 1/2"face, 19t 2
27 Gear wheel 1 1/4"dia, 50t 5
27a Gear wheel 1 1/2"dia,57t 7
27b Gear wheel 3 1/2"dia, 133t 2
28 Contrate Gear 1 1/2" dia, 50t 2
29 Contrate Gear 3/4" dia, 25t 2
30 Bevel Gear 7/8"dia, 26t 4
30a Bevel Gear 1/2"dia, 16t 2
30c Bevel Gear 1 1/2"dia, 48t 2
31 Gear Wheel 1"dia, 1/4"face, 38t 4
32 Worm Gear 2
34 Spanner 2
35 Spring clip 36
36 Screwdriver - Standard Bent Rod 1
36b Screwdriver - Special (steel handled) 1
37 Square Nut and bolt (bolt 7/32" long) 594
37a Square Nut 6
38 Washer 3/8" dia. 200
40 Hank of cord 6
41 Propeller Blade - type 2 4
43 Tension Spring 2" 9
44 Cranked bent strip 3
45 Double bent strip 6
46 Double angle strip 2 1/2x1" 4
47 Double angle strip 2 1/2x1 1/2" 2
47a Double angle strip 3x1 1/2" 2
48 Double angle strip 1 1/2x1/2" 8
48a Double angle strip 2 1/2x1/2" 18
48b Double angle strip 3 1/2x1/2" 12
48c Double angle strip 4 1/2x1/2" 4
48d Double angle strip 5 1/2x1/2" 5
50a 50Eye piece with boss 2
52 Flanged Plate 5 1/2x2 1/2" - 4 flanges (See Note below) 7
52a Flat plate 5 1/2x3 1/2" 11
53 Flanged plate 3 1/2x2 1/2" 7
53a Flat plate 4 1/2x2 1/2" 6
54 Flanged sector plate 4" 4
55a Slotted Strip 2" 2
57b Loaded Hook (large) - ball type 1
57c Loaded Hook (small) - ball Type 14
58 Spring cord 40" 1
58a Coupling Screw for Spring Cord 12
59 Collar 63
62 Crank 14
62a Threaded Crank 2
62b Double Arm Crank 6
63 Coupling 13
63b Strip Coupling 2
64 Threaded boss 4
65 Centre fork 6
70 Flat plate 5 1/2x2 1/2" 7
72 Flat plate 2 1/2x2 1/2" 4
76 Trangular plate 2 1/2" 8
77 Trangular plate 1" 10
78 Screwed rod 11 1/2" 2
80 Screwed rod 5" 2
80a Screwed rod 3 1/2" 2
80b Screwed rod 4 1/2" 2
81 Screwed rod 2" 2
82 Screwed rod 1" 8
89 Curved strip 5 1/2", 10"r 6
90 Curved strip 2 1/2", 2 3/8"r 16
90a Curved strip stepped, 2 1/2", 1 3/8r 10
94 Sprocket chain 20ft
95 Sprocket wheel 2"d, 36t 3
95a Sprocket wheel 1 1/2"d, 28t 4
95b Sprocket wheel 3"d, 56t 2
96 Sprocket wheel 1"d, 18t 10
96a Sprocket wheel 3/4"d, 14t 5
97 Braced girder 3 1/2" 7hole - double closed 5
98 Braced girder 2 1/2" 5hole - double closed 8
99 Braced girder 12 1/2" 25hole - double closed 18
99a Braced girder 9 1/2" 19hole - double closed 2
99b Braced girder 7 1/2" 15hole - double closed 1
100 Braced girder 5 1/2" 11hole - double closed 16
101 Hearld, for loom 60
102 Single bent strip 4
103 Flat girder 5 1/2" 11hole 7
103a Flat girder 9 1/2" 19hole 4
103b Flat girder 12 1/2" 25hole 12
103c Flat girder 4 1/2" 9hole 4
103d Flat girder 3 1/2" 7hole 5
103e Flat girder 3" 6hole 6
103f Flat girder 2 1/2" 5hole 7
103g Flat girder 2" 4hole 2
103h Flat girder 1 1/2" 3hole 6
103k Flat girder 7 1/2" 15hole 2
104 Shuttle, for loom 1
105 Reed hook, for loom 1
106 Wooden roller 2
106a Sand roller 1
107 Table for designing machine 1
108 Architrave (Corner Gusset) 6
109 Face plate 2 1/2"d 11
110 Rack strip 3 1/2" 4
111 Bolt 3/4" 18
111a Bolt 1/2" 24
111c Bolt 3/8" 12
114 Hinge 2
115 Threaded pin - Square Shoulder 9
116 Fork piece, Large 2
116a Fork piece, Small 4
118 Hub disc 5 1/2" dia 4
119 Channel segment 45deg arc, 11 1/2"dia 16
120a Sprung Buffer 6
120b Compression spring 4
121 Train Coupling, Type 3 - pressed steel 2
124 Reverse angle bracket 1" 4
125 Reverse angle bracket 1/2" 9
126 Trunnion 4
126a Flat trunnion 8
128 Bell Crank with boss 2
129 Rack segment 90deg arc, 3"dia 4
130 Eccentric, Triple Throw 2
131 Dredger bucket 5
132 Flywheel 2 3/4" dia 1
133 Corner bracket 1/12" 8
135 Theodolite protractor 1
136 Handrail Support 8
137 Wheel flange 10
140 Universal coupling 2
141 Wire line for clocks 1
142 Rubber ring for 3" dia pulley 3
142a Tyre for 2" dia pulley 4
142b Tyre for 3" dia pulley 4
143 Circular girder 5 1/2" dia 1
144 Dog clutch 1
145 Circular strip 7 1/2" dia 2
146 Circular plate 6" dia 2
147a Pawl with boss 4
147b Pivot Bolt with nuts 8
148 Ratchet wheel 2
155 Flexible ring 5/8" dia 2
157 Fan 2" dia 1
160 Channel bearing 1
161 Girder bracket 2
162 Boiler complete 1
162a Boiler End 1
163 Sleeve piece 3
164 Chimney adapter 2
165 Swivel bearing 2
166 End bearing 6
168 Ball thrust bearing 1
170 130aEccentric, Single Throw 1
171 Socket coupling 1
172 Pendulum connections 1
181 Bobbins 2
182 Insulating brushes 8
1563 Terminals 3
1570 182aInsulating washers 8
1575 6 b.a.screw 9
1583 6 b.a. nut 15
No.2 Clockwork Motor Reversing 1
E6 Electric motor 6V Reversing 1
56c Standard Mechanisms 1
How to use Meccano Parts 1
SML.1 Super Model Leaflet - Motor Chassis 1
SML.2 Super Model Leaflet - Ship Coaler 1
SML.3 Super Model Leaflet - Motorcycle & Sidecar 1
SML.5 Super Model Leaflet - Travelling Bucket Dredger 1
SML.6 Super Model Leaflet - Stiff-Leg Derrick 1
SML.7 Super Model Leaflet - Platform Scales 1
SML.9 Super Model Leaflet - Bagatelle Table 1
SML.10 Super Model Leaflet - Log Saw 1
SML.11 Super Model Leaflet - Horizontal Steam Engine 1
SML.12 Super Model Leaflet - Stone Sawing Machine 1
SML.13 Super Model Leaflet - Meccanograph 1
SML.14a Super Model Leaflet - Grandfather Clock 1
SML.16a Super Model Leaflet - Loom 1
SML.17 Super Model Leaflet - Planing Machine 1
SML.18 Super Model Leaflet - Revolving Crane 1
SML.19 Super Model Leaflet - Steam Shovel 1
SML.20 Super Model Leaflet - Mobile Crane 1
SML.21 Super Model Leaflet - Transporter Bridge 1
SML.22 Super Model Leaflet - Traction Engine 1
SML.23 Super Model Leaflet - Vertical Log Saw 1
SML.24 Super Model Leaflet - Travelling Gantry Crane 1
SML.25 Super Model Leaflet - Hydraulic Crane 1
SML.26 Super Model Leaflet - Twin-Elliptic Harmonograph 1
SML.28 Super Model Leaflet - Pontoon Crane 1
SML.29 Super Model Leaflet - Hammerhead Crane 1
SML.30 Super Model Leaflet - Breakdown Crane 1
SML.31 Super Model Leaflet - Warehouse with Elevators 1
SML.35 Super Model Leaflet - Automatic Grabbing Crane 1
SML.36 Super Model Leaflet - Electric Derrick Crane 1
SML.37 Super Model Leaflet - Howitzer, Limber & Tractor 1

NOTES

1. The 5 1/2" x 2 1/2" flanged plates initially had two flanges on the long sides. The four flanged version was announced in the May 1928 Meccano Magazine. Whilst these lists assume that this happened in 1928, this is not necessarily certain and there might well have been a delay whilst old stock was used up. This especially applies to sets for overseas. There is some evidence to suggest that the 1930 Outfit 000 had the two flanged version.

2. From 1927 to 1934 the 5 1/2" x 2 1/2" flanged plates (both two & four flanged versions) also had a sawcut and slot to accommodate the circular saw (Part No. 159).

3. Originally all bosses were single tapped. In 1926/7 all bosses became double tapped.